How To Explain Fiat Panda Key Fob Replacement To Your Grandparents
Reasons Your Fiat 500 Key Fob Won't Work
A key fob for the Fiat 500 allows you to easily open doors and start your car. However, there are a variety of reasons why the fob may stop working. This could be due to a dead battery or water damage, receiver modules issues, and interference.
This listing is for a NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to find local locksmiths for automotive locksmiths). It comes with lock, unlock and trunk buttons.
Dead Coin Battery
A dead battery is probably the most common cause of your 500 key fob not working. Modern key fobs have a restricted operating range, and must be within just a few feet of the vehicle in order to function. If you are not within your car and hit the keyfob, it will not respond and display the message "Key Fob Not Detected".
If this happens, simply replace the battery on your coin cell (Part number CR2032) with a fresh one from a reliable brand like Panasonic, Duracell, or Energizer. You can find them at the local hardware store or on the internet.
You can test the battery of your coin-cell by pressing the buttons while standing near your Fiat 500. The car should flash its parking lights and the key fob should operate the lock and unlock buttons.
If your key fob still isn't working even after replacing the battery, there might be water damage that prevents it from communicating with the module in your vehicle. Water damage can occur in a variety of ways, from a light splash to submerging the fob in salt water at the beach. If you suspect your fob was exposed to water, try placing it in a dry rice bag to draw the moisture out. If this does not work, you'll require your fob to be changed by an auto locksmith or a dealer.
Water Damage
Although the fob is equipped with rubber seals to keep water out of the electronic chip inside it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short, and eventually end up dying. If you get the fob wet, it's not an ideal idea however, if you drop it into an empty cup of water, or do not remember to take it out of your pants pocket prior to running the washing machine and you don't have a chance, don't give in.
First take the battery off the fob. Clean the electronic chip using isopropyl alcohol or a similar product and dry it completely before replacing the battery. Then try the fob and test if it works. If the key does not work, it may need to be reset. This is typically done by a dealer or professional auto locksmith.
If the key is a newer model and has never been programmed to your vehicle It is likely that it needs to be replaced completely. This is an easy process that can be completed by a professional automotive locksmith. The locksmith must cut the key to match the ignition in your vehicle. The locksmith will also need to reprogram your fob in the car's system. This is a low-cost and quick process that can be completed within the same day.
Receiver Module Issues
One of the simplest reasons why your 500 key fob could stop functioning is that it's out of range. The remote has a range of 30 feet. So if fiat 500 key replacement www.thekeylab.co.uk are too far away from your vehicle it won't be able to respond to your commands. It is possible to solve this problem by moving the remote closer to your car until it responds.
If your fob won't work after you replace the battery for the coin, also known as a "button", "watch" or "button", it may be due to a malfunction on the circuit board inside. In most cases, reprogramming the fob will resolve this issue. There are instructions on how to do this for all vehicles by searching YouTube or consulting the owner's manual.
It is possible to replace the metal clips that hold the coin batteries in their place. If they lose tension, it can prevent the battery from sitting properly and could cause your remote to malfunction.
In rare instances, the fob may become disconnected from your vehicle due to software or hardware issues. This can be a major issue, but you are able to usually fix it by visiting an auto locksmith to have them reprogram your fob for you. In some instances they may have to reinstall the program in your body control module, as well.
Interference
Interference can also cause the key fob to not be able to receive or transmit the signal. This is possible when the key fob is near radio transmitters (cell phones, radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob could not function could be due to a weak connection to the buttons and internal chip or water damage.
If the key fob stopped working one day in the middle of the night and you've tried every option at home to solve it e.g. You could have a malfunctioning 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module, which is located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts the signals into electronic commands which are then read by the vehicle.
Luckily, there is an easy method of resetting all of the on-board systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Then, reconnect the battery. This will get rid of any residual electricity and restart the car's computers. This can help you get your key fob working again. If the problem persists you should seek out an expert technician. They can identify the exact cause of problems.